Latest Items

bathroom vanity woodworking plans

Added/Modified on December 26, 2016
VN:F [1.9.21_1169]
Rating: +1 (from 1 vote)
VN:F [1.9.21_1169]
Rating: 6.5/10 (2 votes cast)

Shopping List:

1 Sheet of 3/4″ Plywood
1 – 1×3 @ 8 feet long
1 – 1×6 @ 4 feet long (optional)
1 – 1×2 – 1/4″ thick stock @ 8 feet long (optional decorative door trim)
1 – 25 foot long roll edge banding for stained finishes
3/4″ finish nails or brad nails if you are applying decorative trim
Either pocket hole screws or countersunk screws/finish nails

2 inch screws
1 1/4 inch finish nails
1 1/4 inch pocket hole screws
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
jigsaw
nailer
sander
level
countersink drill bit

Cut List

1 – 3/4″ Plywood @ 22 1/2″ x 18″
2 – 3/4″ Plywood @ 32″ x 18″
2 – 3/4″ Plywood @ 30 3/4″ x 12″
2 – 1×6 OR 3/4″ Plywood @ 24″
4 – 1×3 @ 24″
Cut trim pieces to fit door faces

General Instructions

Please read through the entire plan and all comments before beginning this project. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain.

Step 1

Cut plywood as shown above, with the grain, cutting long cuts first. So you would cut an 18″ wide strip off of your plywood, and then from that 18″ strip, cut the sides and shelf. You can ask the lumber store to make the cuts for you, and your plywood will be easier to transport and store.

Step 2

Place the bottom shelf as shown above between the sides, either using the Kreg Jig or countersunk screws or 2″ finish nails and wood glue.

Step 3

Attach the 1x3s as shown above. The front 1×3 needs to be placed with a 4″ space above it. The back 1x3s need to be placed at the top, bottom of the bottom shelf, and centered.

Step 4

Now the toekick. Cut out and attach with 2″ finish nails and wood glue.

Step 5

Now the front apron. Same thing.

Step 6

For the front apron, you can glue and attach the 1/4″ trim pieces as shown above.

Step 7

And the doors. You can attach trim pieces as well. The best hinges I’ve found for doors like these (full overlay) are these ones from the Home Depot.

Finishing Instructions

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

VN:F [1.9.21_1169]
Rating: 6.5/10 (2 votes cast)
VN:F [1.9.21_1169]
Rating: +1 (from 1 vote)
bathroom vanity woodworking plans, 6.5 out of 10 based on 2 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally