Latest Items

buffet with drop down TV woodworking plans

Added/Modified on December 13, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 3.0/10 (1 vote cast)


Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Square
Sander
Kreg Jig
Hammer or Brad nailer

Lumber

3 – 1×3 at 8’
1 – 1×3 at 3’
Half sheet of ½” plywood
2 – sheets of ¾” plywood
1 – 1×2 at 4’
1 – 4×4 at 3’

Materials

1-1/4” pocket hole screws
1” pocket hole screws
2” screws
1-1/4” screws
Small nails or 1-1/4” brads
4 – Drawer Handles or knobs
Two sets of hinges (doors)
Continuous hinge (for the top door)
Edge banding for the plywood or Laminate for top
Countersink bit for Drill
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

4 – 1×3 at 15” – Side Frames
4 – 1×3 at 29-1/4” – Side Frames
2 – ½” plywood at 15” x 24-1/4” – Side Panels
1 – ¾” plywood at 20” x 44-1/2” – Bottom
2 – ¾” plywood at 28-1/2” x 44-1/2” – Large Divider & Back
1 – ¾” plywood at 8-1/4” x 28-1/2” – Divider
2 – 1×2 at 21-7/8” – Stretchers
2 – ¾” plywood at 8-1/2” x 21-7/8” – Upper Shelves
2 – ¾” plywood at 7-3/4” x 21-7/8” – Lower Shelves
1 – ¾” plywood at 20-1/2” x 47” – Top
1 – ¾” plywood at 9-3/4” x 37-3/4” – Top Door
2 – 1×3 at 46” – Base Frame
3 – 1×3 at 17” – Base Frame
4 – 4×4 at 3-1/4” – Feet
4 – ¾” plywood at 4-3/4” x 6-3/4” – Drawer Box Sides
2 – 3/4” plywood at 6-3/4” x 20-1/8” – Drawer Bottoms
2 – ¾” plywood at 4-3/4” x 21-5/8” – Drawer Fronts
4 – 1×3 at 16-5/8” – Door Frames
4 – 1×3 at 21-3/4” – Door Frames
2 – ½” plywood at 16-5/8” x 16-3/4” – Door Panels

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Cut the pieces for the side frame. Set the Kreg jig for ¾” material and drill pocket holes in the ends of the shorter pieces. Assemble with glue and 1-1/4” pocket screws as shown.

Cut the plywood piece for the side panels. Set the Kreg jig for ½” material and drill pocket holes as shown. Assemble with glue and 1” pocket hole screws making sure the back of the panel is flush with the back of the frame.

Step 2

Cut the piece for the bottom. Set the Kreg jig for ¾” material and drill pocket holes in the two shorter ends. Attach the sides with the bottom of the frames flush with the bottom face using glue and 1-1/4” pocket hole screws.

Step 3

Cut the piece for the large divider. Drill pocket holes as shown, and secure to the bottom and sides with glue and 1-1/4” pocket hole screws.

Step 4

Cut the pieces for the base. Drill pocket holes in the ends of the three shorter pieces and assemble as shown. Attach the feet to the frame with countersunk 2” screws through the base frame into the feet.

Attach the base to the cabinet with countersunk 1-1/4” screws through the frame into the bottom.

Step 5

Cut the piece for the narrower divider. Drill pocket holes in the bottom and back edges, and secure to the large divider using glue and 1-1/4” pocket hole screws.

Cut the pieces for the stretchers. Drill pocket holes in each end and attach as shown using glue and 1-1/4” pocket hole screws.

Step 6

Cut the pieces for the shelves. Drill pocket holes in the shorter ends of each shelf and secure with the spacing shown using glue and 1-1/4” pocket hole screws. The lower shelves are narrower and are located ¾” back from the front edge.

Step 7

Cut the piece for the back. Drill pocket holes as shown. Attach with glue and 1-1/4” pocket hole screws.

Step 8

Cut the piece for the top. Cut the opening as shown. Secure to the cabinet with ½” overlap at the sides and front using glue and 1-1/4” brad nails through the top into the sides, dividers, and stretchers.

Cut the piece for the door. Cut an optional finger hole at the front of the door to make it easier to open. There will be a 1/8” gap around all sides. The hinge can be placed at the front or back of the opening.

Step 9

Cut the pieces for the drawer boxes. Set the Kreg jig for ¾” material and drill pocket holes in each end of the shorter pieces as well as all four edges of the bottoms. Attach the bottom to the sides with glue and 1-1/4” pocket hole screws.

Cut the pieces for the front and back, and attach using glue and 1-1/4” pocket hole screws.

Step 10

Cut the pieces for the doors and assemble as shown, in the same manner as the sides. There will be a 1/8” gap around all sides of the doors. Attach the hinges to the doors, then shim in place and attach the hinges to the cabinet.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 3.0/10 (1 vote cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
buffet with drop down TV woodworking plans, 3.0 out of 10 based on 1 rating

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox Free PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally