Latest Items

changing table woodworking plans

Added/Modified on November 1, 2015
VN:F [1.9.21_1169]
Rating: -1 (from 1 vote)
VN:F [1.9.21_1169]
Rating: 5.7/10 (9 votes cast)


Materials and Tools

Shopping List:

2 – 1×2 Boards, 8′ Long
1 – Sheet of 3/4″ MDF or Plywood, cut into 15 1/2″ wide and 8′ long strips (these strips will be referred to as 1×16 boards)
1 – 10′ 1×4 Board
4 – 1×3, 8′ Long
12′ of edge beading, 3/4″ thick
2″ Screws
1 1/4″ Screws
1 1/4″ Nails
Wood Glue
Wood Filler
Sand Paper
primer
wood conditioner
paint

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
table saw
nailer
sander

Cut List

4 – 1×2 @ 34″ (Legs)
2 – 1×4 @ 15 1/2″ (Top Trim, Ends)
4 – 1×3 @ 15 1/2″ (Shelf Trim, Ends)
4 – 1×16 @ 40″ (Shelves)
4 – 1×3 @ 38 1/2″ (Shelf Trim, Sides)
2 – 1×4 @ 38 1/2″ (Top Trim, Sides)
2 – 1×3 @ 15 1/2″ (Topper Trim)
2 – 1×3 @ 41 1/2″ (Topper Trim)
1 – 1×2 @ 7 1/4″ (Topper Partition)
1 – 1×2 @ 15 1/2″ (Topper Partition)

General Instructions

Work on a clean level surface. Measure out all joints and mark before fastening. Be safe and use glue. predrill all screw holes before fastening.

Step 1

ENDS

Build your ends as shown above. Use 2″ screws and glue unless you have a Kreg Jig™ and you can fasten the end trim from the insides.

Step 2

SHELVES

Fasten the shelves to the end trim pieces as shown above. Again, 2″ screws and glue or use the Kreg Jig™ from the underside of the shelves. Keep the top edge flush on the shelves.

Step 3

SHELF SIDE TRIM

Trim out the shelf sides as shown above, use 2″ screws and glue. Fasten the trim to the legs to for extra support on the shelves from the outside of the leg or use a Kreg Jig™.

Step 4

Edge Trim

Use 1 1/4″ nails and glue to fasten edge trim around the top of the table, as shown above. Miter your corners at 45 degrees for a neat edge. Cut the edge trim to fit, as dimensions are not shown in the above diagram.

Step 5

TOPPER SIDES

Fasten the topper sides to the remaining 1×16, using glue and 2″ screws or nails.

Step 6

TOPPER SIDES

Attach the side trim to the topper as shown above. Also attach to the end trim from step 5. Use glue and 2″ nails or screws.

Step 7

PARTITIONS

Attach the partitions to the bottom of the topper, and to the side and end trim pieces as shown above. Use glue.

Step 8

ASSEMBLY

From the underside of the changing table, attach the topper with 1 1/4″ screws. Omit the glue if you wish to remove the topper at a future date.

Finishing Instructions

Fill all holes with wood filler. Let dry. Sand with coarse sandpaper. Refill with wood filler. Let dry and sand with medium grit sandpaper. Follow up with fine sandpaper. Vacuum with a soft bristled brush. Wipe clean with a damp cloth. Then prime and paint as desired.

VN:F [1.9.21_1169]
Rating: 5.7/10 (9 votes cast)
VN:F [1.9.21_1169]
Rating: -1 (from 1 vote)
changing table woodworking plans, 5.7 out of 10 based on 9 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes