Latest Items

changing table woodworking plans

Added/Modified on October 23, 2015
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 8.0/10 (1 vote cast)


Shopping List:

4 – 1×2 @ 8 feet long
3 – 1×3 @ 8 feet long
2 – 1×6 @ 8 feet long
3 – 2×2 @ 8 feet long
1/2 sheet 3/4” plywood
2 – 1/8” shims 18” long
200” of 1×4 tongue and groove for door backs
2 sets of hinges

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
compound miter saw
nailer
sander
level
countersink drill bit

Cut List:

2 – 1×2 @ 16 1/2”
2 – 1×3 @ 16 1/2”
6 – 1×6 @ 25 3/4”
4 – 2×2 @ 32 1/4”
4 – 1×3 @ 37 3/8”
1 – 3/4” plywood 18” x 37 3/8”
2 – 2×2 @ 37 3/8”
2 – 3/4” plywood @ 16 1/2” x 12” (could use boards here too and could possibly be made larger as well)
2 – 1/8” thick shims or plywood pieces 18” x 1”

DOORS
4 – 1×2 @ 21 1/2”
4 – 1×2 @ 15 1/2”
1 – 1×2 cross brace – overall length 24 1/2” approximately
10 pieces of 1×4 tongue and groove paneling for door backs 20” long

TOP
1 – 3/4” plywood @ 18” x 38 7/8”
2 – 1×2 @ 41 7/8” (Long point to long point, both ends mitered at 45 degrees)
2 – 1×2 @ 21” (Long point to long point, both ends mitered at 45 degrees)

General Instructions

Please read through the entire plan and all comments before beginning this project. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain.

Step 1

Start by building your sides. For the no pull out wings option, use a 1×3 at the top and extend the 1x6s 1″ longer to meet the tops of the legs. You’ll make two of these.

Step 2

Then attach the legs to the panels to create the two ends.

Step 3

Now we’ll make this a box by adding the front and back trim.

NOTE: If you wish to attach top with PHs drill 3/4″ PHs facing UPWARD on top aprons for later attaching top through.

Step 4

Drill 3/4″ pocket holes around all sides of bottom shelf and attach in place. For additional shelves, you can attach fixed with pocket holes or use shelf pins.

Step 5

These guys are for your pull out wings to slide on. For the non pull out wings option, you won’t need.

Step 6

Now attach the shims to the wings to keep from pulling all the way out and for a secure fit. Definitely do lots of testing here.

Step 7

When you are happy with the wings. let’s get those doors installed. Build the main frame first, then mark your cross board and cut and attach. Then add the backing.

Step 8

Drill 3/4″ PHs around all sides of the top and attach trim, mitering corners, with 1 1/4″ PH screws. Attach to top.

Finishing Instructions:

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

VN:F [1.9.21_1169]
Rating: 8.0/10 (1 vote cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
changing table woodworking plans, 8.0 out of 10 based on 1 rating

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes