Latest Items

console table woodworking plans

Added/Modified on October 30, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 10.0/10 (1 vote cast)

Dimensions:
46 3/4″W x 32″H x 14 1/2″D

Shopping List:

1 – 1×4 @ 10 feet long
1 – 1×6 @ 3 feet long
2 – 1×2 @ 8 feet long
1 – 1×12 @ 8 feet long
1 – 1×12 @ 10 feet long
5- 2×2 @ 8 feet long

¼ sheet of ¼” plywood or hardboard
2 sets 12” white drawer slides euro style bottom corner mount
2 sets narrow profile hinges and magnetic clasps OR Euro Style non mortise butt surface mount hinges

Knobs and handles

2 – 12×12 sheets ¼” acrylic glass and mirror clips
2 inch screws
3/4 inch finish nails
1 1/4 inch pocket hole screws
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
compound miter saw

Cut List

3 – 1×12 @ 43 ¾”
6 – 2×2 @ 11 ¼” (cut to width of 1x12s)
2 – 1×12 @ 13”
2 – 1×12 @ 13 ¾”
4 – 2×2 @ 32”
6 – 2×2 @ 43 ¾”
4 – 1×2 @ 13”
2 – 2×2 @ 17 ¼”
1 – ¼” plywood @ 16” x 46 ¾”

Drawer and Door cut list in instructions

General Instructions

Please read through the entire plan and all comments before beginning this project. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain.

Step 1

Drill ¾” pocket holes along all sides of the shelves (only ends are shown, but go ahead and drill front and back sides too). Attach with 1 ¼” pocket hole screws and glue the end trim, keeping top edges flush.

Step 2

Put one shelf aside (shown at bottom of diagram). From remaining two shelves, attach dividers and sides as shown above, hiding pocket holes to insides. Use ¾” pocket holes and 1 ¼” pocket hole screws and glue.

IMPORTANT: When pre-drilling the pocket holes in the dividers, go ahead and do some on the front and back, as well as the top and bottom. These will help when attaching the face frames.

Step 3

The face frames will use a mixture of 1 ½” and ¾” pocket holes. If you are using any ¾” stock, revert to the ¾” pocket hole and 1 ¼” pocket hole screws. For joints of 1 ½” stock to 1 ½” stock, use 1 ½” pocket holes and 2 ½” pocket hole screws.

As you build the face frames, make sure the frame stays true to measurements and matches up with the storage boxes. Check to make sure door and drawer openings measure true to size.

You will build two of these.

Step 4

Attach face frames to box and bottom shelf through predrilled holes using glue and ¾” pocket hole screws. Add additional fasteners where needed to secure face frame to shelves and storage box.

Step 5

Attach back with 1 ¼” finish nails and glue, nailing to all boards.

Step 6

DRAWERS
4 – 1×4 @ 12 ¾”
4 – 1×4 @ 14 ¾”
2 – 1×6 @ 17”
1 – 1/4″ ply @ 12 3/4″ x 16 1/4″

Build drawer boxes 1” less in width than the opening with 1x4s. Attach plywood to bottom. Attach drawer slides to sides of bottom and install drawer in cabinet. Drawer should sit inset when closed ¾” from outside of cabinet to give room for drawer face.

Step 7

With drawer fully pushed in, align drawer faces up with drawers, with an even 1/8” gap on all sides. Nail on with 1 ¼” finish nails and glue. Remember to avoid areas you will add hardware to.

Step 8

Next build doors from 1×2 stock. When satisfied with doors, test fit with hinges. Add acrylic glass to back using mirror clips. Install clasps to keep doors closed when shut.

Finishing Instructions

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

VN:F [1.9.21_1169]
Rating: 10.0/10 (1 vote cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
console table woodworking plans, 10.0 out of 10 based on 1 rating

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally