Latest Items

entertainment console woodworking plans

Added/Modified on October 25, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)


Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Square
Sander
Kreg Jig

Lumber

9 – 2×2 at 8’
1 – 1×2 at 6’
4 – 1×4 at 8’
2 – 1×8 at 8’
2 – sheets of ¾” plywood

Materials

1-1/4” pocket hole screws
2-1/2” pocket hole screws
Edge banding for plywood, optional
Six sets of 14” drawer slides
Drawer pulls
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

4 – 2×2 at 27-1/2” – Legs
2 – 2×2 at 81” – Front & Back Frame
4 – 2×2 at 26-1/2” – Front & Back Frame
12 – 2×2 at 25” – Front & Back Frame
3 – 3/4” plywood at 20-1/2” x 25” – Back Panel
10 – 2×2 at 14-1/2” – Side Frames & Slide Supports
2 – ¾” plywood at 14-1/2” x 20-1/2” – Side Panels
1 – ¾” plywood at 14- 1/2” x 78” – Top
3 – ¾” plywood at 14-1/2” x 25” – Shelves
6 – ¾” plywood at 13-1/4” x 22-1/2” – Drawer Bottoms
6 – 1×4 at 13-1/4” – Smaller Drawer Sides
3 – 1×4 at 24” – Smaller Drawer Back
3 – 1×4 at 24-3/4” – Smaller Drawer Front
6 – 1×8 at 13-1/4” – Larger Drawer Sides
3 – 1×8 at 24” – Larger Drawer Back
6 – 1×4 (ripped to 3” wide) at 24-3/4” – Larger Drawer Front
3 – 1×2 at 24-3/4” – Larger Drawer Front

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Cut the pieces for the back frame. Cut the miters in each end of the top piece as well as the top of each leg piece. Set the Kreg jig for 1-1/2” material and drill pocket holes in the mitered end of the legs. Also drill pocket holes in the other pieces as shown. The inside leg pieces will have pocket holes drilled in the top only. Assemble the frame using glue and 2-1/2” pocket hole screws.

Cut the pieces for the back panels. Set the Kreg jig for ¾” material and drill pocket holes in all four edges of each panel piece. Position the each panel in the frame and secure using glue and 1-1/4” pocket hole screws. The back of each panel will be flush with the back of the frame.

Step 2

Cut the pieces for the sides. Drill pocket holes in all four edges of the panels. Set the Kreg jig for 1-1/2” material and drill pocket holes in each end of the frame pieces. Attach the frame pieces to the panels using glue and 1-1/4” pocket hole screws. The back face of the panel will be flush with the inside face of the frame pieces. Attach the sides to the back legs using glue and 2-1/2” pocket hole screws through the frame pieces into the legs, and 1-1/4” pocket hole screws through the side panels into the back legs.

Step 3

Cut the pieces for the front frame. Cut the miters in each end of the top piece as well as the top of each leg piece. Set the Kreg jig for 1-1/2” material and drill pocket holes in the mitered end of the legs. Also drill pocket holes in the other pieces as shown. The inside leg pieces will have pocket holes drilled in the top only. Assemble the frame using glue and 2-1/2” pocket hole screws.

Step 4

Cut the piece for the top. Set the Kreg jig for ¾” material and drill pocket holes in all four edges. Secure to the front frame, sides, and back frame using glue and 1-1/4” pocket hole screws. The top face of the top will be flush with the top faces of the front, sides, and back.

Step 5

Cut the pieces for the slide supports. Set the Kreg jig for 1-1/2” material and drill pocket holes in each end. The upper supports will be positioned so the top is flush with the top of the corresponding front frame piece. The bottom of the middle and lower supports will be flush with the top of the corresponding frame pieces. Secure using glue and 2-1/2” pocket hole screws.

Step 6

Cut the pieces for the shelves. Set the Kreg jig for ¾” material and drill pocket holes in all four edges. Secure to the front frame, sides, and back using glue and 1-1/4” pocket hole screws. The top face of the shelves will be flush with the top faces of the front frame.

Step 7

Cut the pieces for the fronts of the larger drawers. The fronts will be pieced so they look like the smaller drawers. Assemble as shown using glue and 1-1/4” pocket hole screws. Cut the remaining pieces for the drawers. Drill pocket holes in each end of the side pieces as well as all four edges of the bottom. Assemble as shown using glue and 1-1/4″ pocket hole screws. The fronts will overlap the drawer box by 3/8″ on each side. There will be a 1/8” gap around all sides of the drawer fronts in the opening. Install the drawer slides according to the manufacturer’s instructions. Make any necessary adjustments.. Make any necessary adjustments. Install the drawer pulls.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox Free PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally