Latest Items

farmhouse bed with arch woodworking plans

Added/Modified on November 2, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 7.3/10 (6 votes cast)


Dimensions:
Queen – can easily convert to other sizes

Materials and Tools

Shopping List for Queen

6 – 1×6 @ 8 feet long
7 – 1×4 @ 6 feet long
1 – 1×10 @ 6 feet long
2 – 4×4 posts, 8 feet long
2 – 2×4 @ 8 feet or stud length
2 – 2×6 @ 8 feet or stud length

wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush

Tools:

measuring tape
square
safety glasses
hearing protection
drill
circular saw
jigsaw
nailer
sander

Cut List
A) 11 – 1×6 @ 30″ (panels for the headboard)
B) 11 – 1×6 @ 15″ (panels for the footboard)
C) 7 – 1×4 @ 60 1/2″ (top and bottom trim for the headboard and footboard panels)
D) 1 – 1×10 @ 60 1/2″ (arch cutout for the arched header)
E) 2 – 4×4 posts @ 54 1/2″ (Headboard posts)
F) 2 – 4×4 posts @ 21″ (Footboard Posts
G) 2 – 2×4 @ 67 1/2″ (Top of Panels and Posts for Footboard and Headboard)
H) 2 – 2×6 @ 69 1/2″ (Top of Headboard and Footboard)

Siderails and Frame Pieces (optional if you have a bed frame)

I) 2 – 2×4 @ 84 3/4″ (Cleats for the Siderails)
J) 1 – 2×4 @ 57″ (Footboard piece of the frame)
K) 2 – 1×10 @ 80″ (Siderails)

Cutting Instructions:

This plan assumes that your 1x6s are 5 1/2″ wide. Measure yours – if they are not, you could find your panel is short or long on your panel trim. Adjust accordingly. Best advice is to not cut any boards until after you have constructed and measured your panel boards.

Step 1

Start with 2 of the pieces C, the 1×4 trim pieces. Begin by lining up the panel pieces for the headboard, A, on top of the 2 trim pieces, C, as shown above. Use glue and 1 1/4″ nails to nail through the panel pieces, A, into the back side of C. Check for square. Nail all 11 headboard pieces to the back side of C.

Do the same for the footboard, this time using the panel pieces B, and two more of the 1×4 trim pieces, C.

Step 2

Your Headboard and Footboard panels should look like the above diagram. Make sure these panels are square.

Step 3

Begin with piece D, and cut out with a jigsaw the desired arch. The arch used above begins 5 1/2″ on either end and reaches up 6″ at the highest point in the center. After the arch is cut out of the header piece, D, for the headboard, flip the larger panel over, as shown above, and secure the header piece, D, as shown above, using 2″ nails and glue. Keep all outside edges flush.

Step 4

Mark the 4×4 posts 5/8″ in on either end on the side that will be connected to the center panel. Line up the center panel with these marks to center the panel on the 4×4 post as shown above. Predrill 1/2 way through the post and then screw with 4 1/2″ screws through the predrilled hole into the center panel. Make sure you are lining up your screws with the panel where it is sandwiched 3 boards thick.
Do the same with the footboard pieces, using the shorter posts and the footboard panel.

Step 5

Position G on top of the headboard, as shown above. Use screws to screw piece G to the top of the headboard, making sure to screw into the posts and center panel. Line up all outside edges and keep flush.

Step 6

Then add H, the 2×6 top piece, as shown above, over pieces G, to both the headboard and footboard. There will be a 1″ overhand on all sides.

Step 7

Attach the cleats (I), as shown above, with the bottom edge 9 1/2″ from the bottom. Predrill and use long screws to secure, 4 screws per cleat.

Step 8

Next add the end piece for the cleats, J, inset to the cleats as shown above. Use long screws, 3 per end, predrilling through the cleat (I) into the end edges of J.

Step 9

Now position the footboard so that piece J lays flush with the panel piece, as shown above. Use 2″ screws to screw through J into the footboard, screwing all the way down J. Make sure the cleats are level.

Step 10

Add the siderail pieces, keeping the bottom edge of the siderail, K, flush with the cleats (I). Use screws to screw from the inside of the cleat, through the cleat and into the siderail. Predrill and use 2″ screws, screwing down the length of the siderail.

Finishing Instructions

Fill screw holes with putty, sand and finish as desired.

VN:F [1.9.21_1169]
Rating: 7.3/10 (6 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
farmhouse bed with arch woodworking plans, 7.3 out of 10 based on 6 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally