Latest Items

farmhouse sofa or entry table woodworking plans

Added/Modified on September 20, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)

Dimensions:
96″ x 30″ x 30″

Shopping List:

2 – 2×2 Boards, 8′ Long ($2 Each for pine)
4 – 1×8 Boards, 8′ Long ($7 Each for pine)
2 – 1×3 Boards, 8′ Long ($1.50 Each for pine)
1 – 1×4 Board, 10′ Long ($4 Each for pine)
2 – 1×6 Boards, 10′ Long ($6 Each for pine)
1 1/4″ and 2″ Finish Nails
2″ Wood Screws (about 100)
2 1/2″ Wood Screws (about 20 screws)
Wood Glue
Wood Filler
Sandpaper
Finishing Supplies
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
drill
circular saw
nailer
sander

Cut List:

4 – 1×3 @ 29 1/4″ (Table End Legs)
4 – 1×4 @ 29 1/4″ (Table Side Legs)
2- 1×6 @ 88″ (Side Aprons)
2 – 1×6 @ 23 3/4″ (End Aprons)
2 – 1×3 @ 23 3/4″ (End Stretcher)
8 – 2×2 @ 23 3/4″ (Under Tabletop Supports)

Cutting Instructions:

This table is highly customizeable to fit your needs. Note that the tabletop expects your tabletop boards (the 1x8s) to be 7 1/2″ wide. If your 1x8s are not 7 1/2″ wide, adjust accordingly.

General Instructions

Work on a clean level surface. Check for square after each step. Use straight lumber. Measure and confirm your cuts before cutting. Dryfit your boards before fastening. Always use glue. Predrill and countersink screws. Use saftey precautions and protective eye and hearing gear.

Step 1

End Legs. Taper your end leg pieces as shown above. Cut the taper in a straight line, starting 5 1/2″ from the top, and tapering in 1″ at the bottom. This is shown above. Do this on all four legs. The end legs are made of 1×3 boards.

Step 2

Side Legs. Taper the side legs as you did the end legs from step 1. The side legs are made of 1x4s . Use the measurements above to guide you.

Step 3

Leg Assembly. Assembly your legs as shown above. Be aware of the leg postion on the table as you assemble, as the legs will be assembled different depending on the position. Remember, the 1×3 leg sides are on the ends, the 1×4 leg sides are on the sides of the table. This is shown above.

Step 4

Side Aprons. Fasten the side aprons in place as shown above. Make sure you take a square of the legs as you do this. This is shown above.

Step 5

End Aprons and End Stretcher. Fasten the end apron and end stretcher in place, as shown above.

Step 6

Under Tabletop Supports. Attach the tabletop supports as shown here. Use the measurements above to guide you.

Step 7

Tabletop Pieces. Start by finding the center of your table. Mark and place your table top piece, using the center mark for your first boards. Only attach on the ends in this step, using the screw pattern above. DO NOT ATTACH IN THE CENTER. Attach the remaining tabletop pieces on the ends only.

Step 8

Tabletop Pieces. From the underside, fasten through the under tabletop support pieces into the tabletop pieces. Start with the middle boards and work your way out. Minimize any gaps between the boards. Predrill and countersink your screws. To further strengthen the table, you can add simpson strong tie corner brackets to the corners.

VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally