fire station loft bed woodworking plans
- step 1
- step 2
- step 3
- step 4
- step 5
- step 6
- step 7
- step 8
- step 9
- step 10
- step 11
- step 12
- step 13
- step 14
- step 15
- step 16
- step 17
- step 18
- step 19
Dimensions:
Fits Twin mattress.
Materials and Tools
Shopping List:
14 – 1×3 Boards @ 8 feet long
3 – 1×8 @ 8 feet long
10 – 1×2 @ 8 feet long
2 – 1×6 @ 8 feet long
1 – 1×4 @ 10 feet long
1 – sheet 3/4″ plywood, 8’x4′
slats not accounted for in cut list
2 1/4″ or 2 3/8″ screws (about 50) for assembly
2 inch screws
1 1/4 inch finish nails
2 inch finish nails
1 1/4 inch pocket hole screws
wood glue
wood filler
Tools:
measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
jigsaw
nailer
sander
countersink drill bit
Cut List
2 – 1×3 @ 79 1/2″
2 – 1×8 @ 79 1/2″
44 – 1×2 @ 15 1/4″ (Railing)
4 – 1×3 @ 15 1/4″ (Railing)
10 – 1X3 @ 73″ (Legs)
1 – 1×6 @ 79 1/2″
2 – 1×3 @ 42 1/2″
1 – 1×3 @ 38″
1 – 1×8 @ 38″
2 – 1×3 @ 9 1/4″
2 – 1×8 @ 9 1/4″
4 – 3/4″ Plywood @ 48″ x 9 1/4″
2 – 3/4″ Plywood @ 48″ x 22 1/2″
2 – 2×4 @ 74 1/2″
Slats cut at 39 1/2″
TRIM (Full Side)
2 – 1×6 @ 6 3/4″
2 – 1×3 @ 6 3/4″
2 – 1×3 @ 49″
1 – 1×2 @ 38″
TRIM (Ladder Side)
2 – 1×6 @ 9 1/4″
2 – 1×3 @ 9 1/4″
2 – 1×2 @ 9 1/4″
1 – 1×8 @ 18″
4 – 1×3 @ 18″
TRIM (Front)
1 – 1×2 @ 74 1/2″
2 – 1×3 @ 16 1/2″
2 – 1×6 @ 16 1/2″
2 – 1×4 @ 49 1/2″
2 – 1×2 @ 11 1/2″
1 – 1×8 @ 34 1/2″ – cut arch shape out
General Instructions
Please read through the entire plan and all comments before beginning this project. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain.
Step 1
This bed is shown built with PureBond Formaldehyde Free Plywood in Birch. You will need one sheet of plywood, cut carefully as shown above. Make sure you consider the saw blade width as you cut. Cut, measure, cut, measure and so on. Save the scrap piece to use as a decorative front.
Step 2
You will need to build two of these. Mark the tops and bottoms as shown in diagram. Drill Kreg Jig pocket holes on each end of each slat, as shown in diagram. Attach with pocket holes and glue.
Step 3
Take one of the completed railings and attach it to 1×3 legs with 1 1/4″ finish nails and wood glue. Then attach the bottom 1×6 to the bottom as shown in diagram. Take a diagonal to make sure the back is square and adjust if necessary – this is very important to ensuring your bed is square.
Step 4
Now simply fill in the empty spaces with 1x3s and 1 1/4″ finish nails. Keep the outside edge flush to make the legs look like solid blocks. This completes the back, set aside.
Step 5
Build the full side railing as shown above. Also use a jigsaw to cut an arch shape from the bottom 1×8 as shown in diagram.
Step 6
Attach smaller pieces of plywood to bottoms of the 1×8 as shown in diagram.
Step 7
With pocket holes facing up, lay the panel down on top of 1x boards, to raise 3/4″ above your work surface. Attach sides with either 3/4″ pocket holes and 1 1/4″ pocket hole screws or 2″ screws or finish nails from outsides and glue.
Step 8
Add trim as shown in diagram, using 1 1/4″ finish nails and wood glue. This completes the full side, set aside.
Step 9
On the ladder side, construct two panels as shown above.
Step 10
With pocket holes facing upward, elevate 3/4″ using 1x boards and attach sides with either pocket holes or 2″ fasteners and glue.
Step 11
Followed by trim.
Step 12
And then add the ladder pieces to create the ladder. This completes the ladder side panel, set aside.
Step 13
For the front, use the remaining top railing and attach to the large pieces of plywood. You may wish to cut the windows out prior. Use 1 1/4″ pocket holes through 3/4″ pocket holes to attach. Note that the windows are not exactly centered on the panels, with the smaller margin to the outsides.
Step 14
Lay remaining 1×3 legs on top with outside edges flush and glue and nail down with 1 1/4″ finish nails.
Step 15
Fun step time for trim!
Step 16
With your scrap piece of plywood cut out a decorative gable end, with window, and trim with 1x2s. Attach above doorway to railing with 1 1/4″ finish nails and glue. This completes the front panel, it’s time to assemble!
Step 17
From the insides of the bed, use 2 1/4″ screws to attach panels to each other, keeping outside edges flush to create the illusion of a solid leg. Screws should be every 6-8 inches, from bottom all the way to top. Predrill holes.
Step 18
You can actually do this on the ground before assembly – add 2×4 cleats to front and back panels. This will create considerable strength and give you something to set your bunkie board or slats on.
Step 19
When it comes to slats, you should always refer to the mattress recommendations or use a bunkie board. Make sure you screw slats down if you choose to use slats. To further beef up the bed, add two more 2x4s running parallel to the cleats on either side of the ladder (for example, you wish to create a full size loft bed).
Finishing Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
fire station loft bed woodworking plans,