Latest Items

kids picnic table woodworking plans

Added/Modified on September 12, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 7.0/10 (6 votes cast)

Dimensions:
Table: 34 1/2″ x 19 1/2″ x 16″ Bench(2): 31″ x 11 1/2″ x 8″

Materials and Tools

Shopping List:

4 – 2×4 Boards (about $2.00 Each)
1 – 2×2 Board (about $1.50 Each)
3 – 1×4 Boards (about $3 Each)
1 1/4″ Screws
2 1/2″ Screws
Wood Glue
Wood Filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush

Tools:

measuring tape
square
pencil
hammer
safety glasses
hearing protection
drill
compound miter saw
sander
level

Cut List

Table

4 – 1×4 @ 21 1/2″ (DO NOT CUT until reviewing step 1, ends are mitered at 45 degrees)
8 – 1×4 @ 10 1/4″ (Cut to measurement, ends mitered down 45 degrees)
2 – 2×2 @ 19 1/2″ (Ends of Tabletop)
5 – 2×4 @ 31 1/2″ (Tabletop Boards)

Cut List for TWO Benches

8 – 1×4 @ 9 1/4″ (Both ends mitered at 45 degrees, review step 4 before cutting)
16 – 1×4 @ 4 5/8″ (CUT TO MEASUREMENT One end mitered back at 45 degrees)
4 – 2×2 @ 11 1/2″ (Ends of Tabletop)
6 – 2×4 @ 28″ (Seat Boards)

General Instructions

Work on a clean level surface. Use your square to check to make sure the angles between the legs are a correct 90 degrees. Use proper safety precautions and equipment. Predrill and countersink your screw holes.

Step 1

Legs. Cut your legs so that the ends are mitered at 45 degrees, and the short point to long point measurements are 20 1/2″ as shown above. Then mark all four of the legs as shown on the blue leg above. Use the marks to guide you as you fasten with glue and 1 1/4″ screws the two legs together. To hide your screw holes, fasten from the insides of the legs.

Step 2

Fill in the Legs. Measure and cut the remaining leg pieces, shown in blue above, to fit the missing pieces on the legs. Use glue and 1 1/4″ screws to fasten together. Hide your screw holes on the inside.

Step 3

Top. Begin by fastening with glue and 2 1/2″ screws the ends (shown in blue above) to the tabletop boards. Leave a 1/2″ gap between the boards. Then attach the ends to the legs using 2 1/2″ screws. You will notice in this table’s design there is good water drainage and no pockets for water to remain and cause damage.

Step 4

Bench Legs. Build your bench legs as you built your table legs in step 1. Use 1 1/4″ screws and glue on this step.

Step 5

Bench Leg Pieces. Fill in the bench leg pieces as you did the table leg pieces from step 2. Use 1 1/4″ screws and glue.

Step 6

Bench Seats. As you built the tabletop, do the same for the bench seats.

Finishing Instructions

Fill nail holes with wood filler and sand and finish as desired. To get the two tone finish, you may wish to finish the tops and the X bases before assembling.

VN:F [1.9.21_1169]
Rating: 7.0/10 (6 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
kids picnic table woodworking plans, 7.0 out of 10 based on 6 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox Free PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally