Latest Items

King Stria Bed woodworking plans

Added/Modified on August 15, 2015
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 5.4/10 (5 votes cast)

Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Countersink Bit for Drill
Square
Sander
Kreg Jig
Brad Nailer

Lumber

2 – 2×2 at 6’
6 – 1×2 at 8’
One sheet of ¾” plywood
2 – 1×4 at 8’
15 – 1×3 at 8’
One sheet of ¼” plywood

Materials

1-1/2” pocket hole screws
1-1/4” screws
5/8” brad nails
Surface mounted keyhole bed rail brackets (like these)
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

2 – 2×2 at 18” – Footboard Legs
2 – 2×2 at 50” – Headboard Legs
4 – 1×2 at 75” – Headboard & Footboard Frames
1 – ¾” plywood at 4-1/2” x 75” – Footboard Panel
1 – ¾” plywood at 36-1/2” x 75” – Headboard Panel
2 – 1×4 at 84” – Sides
2 – 1×2 at 81” – Slat Supports
17 – 1×3 at 76-1/2” – Slats
18 – ¼” plywood at 1-1/2” x 76-1/2” – Trim Slats

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Cut the pieces for the legs and headboard/footboard frames. Set the Kreg jig for ¾” material and drill pocket holes in each end of the frame pieces. Attach to the legs using glue and 1-1/2” pocket hole screws as shown in the drawings.

Step 2

Cut the pieces for the headboard/footboard panels. Drill pocket holes as shown. Attach to the frames using glue and 1-1/2” pocket hole screws. The faces of the panels will be flush with the faces of the frames.

Step 3

Cut the pieces for the sides and slat supports. Attach the slat supports to the sides using glue and countersunk 1-1/4” screws. The bottom of the supports will be flush with the bottom of the sides. Attach the bed hardware according to the manufacturer’s instructions.

Step 4

Cut the pieces for the slats. Attach to the supports using countersunk 1-1/4” screws. Do not use glue!

Step 5

Cut the pieces for the trim slats. Attach to the headboard and footboard as shown with approximately ½” spacing using glue and 5/8” brad nails.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 5.4/10 (5 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
King Stria Bed woodworking plans, 5.4 out of 10 based on 5 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes