Latest Items

media stand woodworking plans

Added/Modified on April 6, 2016
VN:F [1.9.21_1169]
Rating: -1 (from 1 vote)
VN:F [1.9.21_1169]
Rating: 6.3/10 (4 votes cast)

Shopping List:

2 – 1×12 @ 8 feet long
1 – 1×12 @ 6 feet long
3 – 1×2 @ 8 feet long
2 – 1×3 @ 8 feet long
1 – 1×1 moulding 8 feet long
2-3 sets of surface mount hinges
3 knobs
1 1/4″ pocket hole screws

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
compound miter saw
sander

Cut List:

1 – 1×12 @ 52 1/2″
2 – 1×12 @ 21 1/4″
2 – 1×2 @ 51 3/4″
2 – 1×4 @ 51 3/4″
4 – 1×2 @ 21 3/4″
2 – 1×2 @ 16 1/4″
2 – 1×12 @ 17 3/4″
3 – 1×12 @ 17″
1 – 1/4″ plywood 21 1/4″ x 54 3/4″
1 – 1×12 @ 57 1/2″
1 – 1×3 @ 57 1/2″

DOORS
6 – 1×3 @ 16″
6 – 1×3 @ 11″
1×1 slats have 11″ exposed overall per grid
1/4″ plywood for back measures 51 3/4″ x 21 1/4″

Step 1:

Start by building the basic box for the media console. To conserve wood, a top is not necessary. You’ll just have to be extra attentive to make sure the face frames are attached square.

Step 2:

Build your back face frame first, then attach to back.

TIP: Consider adding the two additional 1x2s as done on front face frame just to finish out shelf dividers.

Step 3:

Build front face frame and attach to front. Note that both back and front face frames over extend the ends by 3/8″.

Step 4:

Place middle dividers in the cabinet and attach by drilling 3/4″ pocket holes around bottom and side edges. Attach with glue and screws.

Step 5:

Now add the shelves. To make the shelves match the door grids, attach as shown in picture above.

Step 6:

Attach back.

Step 7:

Build top first, then attach top to cabinet as shown in Step 7 picture above, with equal overhangs on ends and front.

Step 8:

Build doors and attach with hinges to the front of the cabinet.

Finishing Instructions:

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

VN:F [1.9.21_1169]
Rating: 6.3/10 (4 votes cast)
VN:F [1.9.21_1169]
Rating: -1 (from 1 vote)
media stand woodworking plans, 6.3 out of 10 based on 4 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes