Latest Items

nestling tables woodworking plans

Added/Modified on November 29, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)

Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
1” Paddle bit or hole saw
Square
Sander
Kreg Jig
Brad nailer

Lumber

5 – 1×2 at 8’
2 – 1×4 at 8’
1 sheet of ¾” plywood

Materials

1-1/4” pocket hole screws
1-1/4” brad nails
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

Small Table
2 – 1×4 at 13” – Sides
4 – 1×2 at 18-1/4” – Legs
2 – 1×2 at 16” – Side Bottom
2 – 1×2 at 12-1/4” – Front & Back Stretchers
1 – 1×4 at 12-1/4” – Back
1 – ¾” plywood at 12-1/4” x 15-1/4” – Bottom
1 – ¾” plywood at 13-3/4” x 16” – Top
4 – ¾” plywood at 1-3/4” x 12” – Drawer Sides, Front & Back
1 – ¾” plywood at 10-1/2” x 12” – Drawer Bottom

Medium Table
2 – 1×4 at 14” – Sides
4 – 1×2 at 23” – Legs
2 – 1×2 at 17” – Side Bottom
2 – 1×2 at 14-3/4” – Front & Back Stretchers
1 – 1×4 at 14-3/4” – Back
1 – ¾” plywood at 14-3/4” x 16-1/4” – Bottom
1 – ¾” plywood at 16-1/4” x 17” – Top
2 – ¾”plywood at 1-3/4” x 13” – Drawer Sides
2 – ¾” plywood at 1-3/4” x 14-1/2” – Drawer Front & Back
1 – ¾” plywood at 13” x 13” – Drawer Bottom

Large Table
2 – 1×4 at 15” – Sides
4 – 1×2 at 27-3/4” – Legs
2 – 1×2 at 18” – Side Bottom
2 – 1×2 at 17-1/4” – Front & Back Stretchers
1 – 1×4 at 17-1/4” – Back
1 – ¾” plywood at 17-1/4” x 17-1/4” – Bottom
1 – ¾” plywood at 18” x 18-3/4” – Top
2 – ¾”plywood at 1-3/4” x 15” – Drawer Sides
2 – ¾” plywood at 1-3/4” x 17” – Drawer Front & Back
1 – ¾” plywood at 15” x 15-1/2” – Drawer Bottom

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Each table is constructed in the same manner.

Cut the pieces for the sides. Set the Kreg jig for ¾” material and drill pocket holes in one end of each leg, as well as each end of the 1×4 piece. Assemble as shown using glue and 1-1/4” pocket hole screws.

Step 2

Cut the pieces for the back. Drill pocket holes in each end of each piece. Attach to the legs as shown using glue and 1-1/4” pocket hole screws.

Cut the piece for the front stretcher and drill pocket holes in each end. Attach to the top of the front legs using glue and 1-1/4” pocket hole screws.

Step 3

Cut the piece for the bottom and drill pocket holes in three edges (to attach to the sides and back). Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 4

Cut the piece for the top. Secure using glue and 1-1/4” brad nails.

Step 5

Cut the pieces for the drawer. Cut the pieces for the sides and the bottom. Attach the sides to the bottom using glue and 1-1/4” brad nails.

Cut the pieces for the front and back. Drill a 1” hole at the center of the front, approximately 1” down from the top edge. Attach the front and back to the sides and bottom using glue and 1-1/4” brad nails.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 0.0/10 (0 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes