Latest Items

shoe storage woodworking plans

Added/Modified on December 14, 2016
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 7.2/10 (6 votes cast)

Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Square
Sander
Kreg Jig
Brad Nailer

Lumber

1 scrap of 1×2 at least 25”
2 scraps of 1×4 at least 7-1/2”
Quarter sheet of 1/4″ plywood, lauan, or hardboard
One sheet of ¾” plywood

Materials

1-1/4” pocket hole screws
1-1/4” brad nails
Edge banding for plywood
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

2 – ¾” plywood at 11-3/4” x 39” – Sides
5– ¾” plywood at 11-3/4” x 25” – Shelves, Top & Bottom
2 – ¾” plywood at 11-3/4” x 33-1/4” – Dividers
1 – 1/4″ plywood, lauan, or hardboard at 26-1/2″ x 39″ – Back
1 – 1×2 at 25” – Trim
2 – 1×4 at 7-1/2” – Trim

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

If using edge banding, apply to the plywood before assembly.

Cut the pieces for the sides and shelves. Set the Kreg jig for ¾” material and drill pocket holes at each end of the shelves. Set two of the shelves aside for the cubbies and assemble the remaining two shelves with the sides using glue and 1-1/4” pocket hole screws as shown in the drawing.

Step 2

Cut the pieces for the trim. Cut a decorative curve in the 1×4 pieces and attach to the 1×2 as shown with glue and 1-1/4” brad nails through the 1×2 into the trim pieces.

Attach the trim under the bottom piece on the cabinet with glue and 1-1/4” brad nails through the 1×2 into the bottom.

Step 3

Cut the piece for the back. Attach with glue and 1-1/4” brad nails.

Step 4

Cut the notches in the remaining shelves as shown. Attach to the cabinet using glue and 1-1/4” pocket hole screws.

Step 5

Cut the pieces for the dividers. Cut the notches as shown. Slide onto the shelves and attach to the cabinet with glue and 1-1/4” brad nails.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 7.2/10 (6 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
shoe storage woodworking plans, 7.2 out of 10 based on 6 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally