Latest Items

shoe storage woodworking plans

Added/Modified on November 13, 2015
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 6.7/10 (6 votes cast)


Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Square
Sander
Kreg Jig
Brad Nailer

Lumber

2 sheets of ¾” plywood
1 sheet of ¼” plywood, lauan, or hardboard
1 – 1×2 at 6’
1 – 1×4 at 4’

Materials

1-1/4” pocket hole screws
1-1/4” brad nails
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

2 – ¾” plywood at 11-3/4” x 86” – Sides
9 – ¾” plywood at 11-3/4” x 25” – Shelves & Cubbies
2 – ¾” plywood at 11-3/4” x 76” – Dividers
2 – 1×2 at 25” – Trim
4 – 1×4 at 7-1/2” – Trim
1 – ¼” plywood, lauan, or hardboard at 26-1/2” x 77-1/2” – Back

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Cut the pieces for the sides and the shelves. Set the Kreg jig for ¾” material and drill pocket holes at each end of the shelf pieces. Set seven of the shelf pieces off to the side for the cubbies. Attach the shelves to the sides at the spacing shown using glue and 1-1/4” pocket hole screws.

Step 2

Cut the piece for the back. Attach to the cabinet with glue and 1-1/4” brad nails.

Step 3

Cut the pieces for the trim. Cut a fancy curve or design of your choice in the 1×4 pieces and attach to the 1×2 with glue and 1-1/4” brad nails. The face of the trim pieces will be flush with one of the edges of the 1×2.

Attach the trim assembly to the cabinet top and bottom with glue and 1-1/4” brad nails.

Step 4

Cut the notches in the shelves for the cubbies as shown with a jigsaw. Attach to the sides at the spacing indicated using glue and 1-1/4” pocket hole screws.

Step 5

Cut the pieces for the dividers. Cut the notches as shown using a jigsaw. Attach to the cabinet with glue at the spacing indicated and add a few brad nails through the shelf into the dividers.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 6.7/10 (6 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
shoe storage woodworking plans, 6.7 out of 10 based on 6 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
Free PowerPoint Templates - PowerPoint Slides - TagFox Memes