storage bench woodworking plans
18″ High, 48″ Wide, 15″ Deep
Materials and Tools
1 – 12′ 1×12 pine board
2 – 1×2 pine boards
1 – 1×3 pine board
2 – 1×4 pine boards
2 – sets of basic butteryfly hinges
2 inch screws
1 1/4 inch pocket hole screws
120 grit sandpaper
2 – 1×12 @ 42 1/2″ (Shelves)
4 – 1×2 @ 17 1/4″ (Leg Pieces for the Sides)
4 – 1×3 @ 17 1/4″ (Leg Pieces for the Front and Back)
2 – 1×2 @ 39″ (Bottom Shelf Trim, Front and Back)
2 – 1×4 @ 39″ (Top Storage Compartement Sides, Front and Back)
2 – 1×2 @ 8 1/2″ (Bottom Shelf Trim, Sides)
2 – 1×4 @ 8 1/2″ (Top Storage Compartment Sides, Sides)
1 -1×4 @ 48″ (Top, Back)
1 – 1×12 @ 48″ (Hinged Top)
Legs and Bottom Shelf. Begin by building all four legs. You will need to nail through the 1×2 part of the leg into the 1×3 leg piece, keeping outside edges flush. Notice how the 1×3 part of the legs is on the front and back, and the 1×2 parts are on the sides. Be aware of the leg placement as you assemble the bench.
Then fasten the legs to the bottom shelf, leaving a 3″ clearance under the bottom shelf on each of the legs. I suggest that you mark each of the legs 3″ from the bottom first, and then assemble the bench. Use glue and 2″ nails, fastening through all the leg pieces into the shelf edges.
Top Shelf. Fasten the top shelf, leaving 2 3/4″ from the top of the shelf and the top of the bench. As you did in step 1, I recommend marking each of the legs 2 3/4″ down from the top, and lining this mark up with the top of your top shelf. Fasten through the legs into the shelf with the 2″ nails and glue.
Bottom Shelf Trim. Measure and cut your bottom shelf trim from 1x2s. These are pieces noted as pieces D and should be approximately 39″ long. Trim both the front and back of the bench. Keep the bottom edges flush. The top will overextend by 3/4″ the bottom shelf. Use the 2″ nails and glue.
Top Shelf Storage Compartment Sides, Front and Back. Measure and cut pieces E, a 1×4 approximately 39″ long. Keeping the bottom edge flush with the bottom of the top shelf, fasten E to the top shelf along the bottom edge. Use the 2″ nails and glue. Then toenail, or nail at an angle from the top ends of E into the sides of the leg pieces. This will keep the top edges of the storage compartment in place.
Storage Compartment Sides. Measure and cut the storage compartment sides, as shown above. These are pieces G and should be approximately 8 1/2″ long, cut from 1×4 boards. Fasten in place as you did the front and back in step 4.
Bottom Shelf Trim, Sides. As you did in step 3, measure and cut boards F and trim out the sides of the bottom shelf. Boards F should be approximately 8 1/2″ long, cut from 1x2s, and are flush with the bottom of the bench.
Top, Back Piece. Mark piece H 2″ from the outsides for the overhang on the ends. Then mark piece H 1″ along the back edge for the back overhang. Then position piece H on top of the bench and fasten in place using the 2″ nails and glue. Be sure to fasten to the leg pieces and the back of the storage compartment.
Hinged Top. Use the hinges to attatch the 1×12 to the 1×4. It is a good idea to use magnetic clasps to keep the 1×12 in place and prevent warping when the top is closed. Look closely at the first picture and you will see the hinges slightly show on top of the bench. If you would like completely invisible hinges, you can invest in support hinges designed for lift top toy boxes and benches. The cheap butterfly hinges work great for me.