Latest Items

Stria Nightstand Woodworking Plans

Added/Modified on December 7, 2015
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
VN:F [1.9.21_1169]
Rating: 7.3/10 (3 votes cast)


Tools

Tape Measure
Saw – Jig, Circular, or Miter
Drill
Countersink Bit for Drill
Square
Sander
Kreg Jig
Brad Nailer

Lumber

Half sheet of ¾” plywood
Half sheet of ¼” plywood
½” plywood at 2’ x 2’
1 – 1×3 at 6’
2 – 1×8 at 6’

Materials

1-1/2” pocket hole screws
1” screws
5/8” brad nails
Edge banding for plywood
Two sets of 16” drawer slides
Wood filler
Sandpaper
Wood glue
Finishing Supplies

Cut List

1 – ¾” plywood at 16-1/2” x 17-1/4” – Bottom
2 – ¾” plywood at 17-1/4” x 20-1/4” – Sides
1 – ¾” plywood at 17-1/4” x 18” – Top
1 – ¼” plywood at 18” x 21” – Back
2 – 1×3 (ripped to 2” wide) at 14-1/4” – Pedestal
2 – 1×3 (ripped to 2” wide) at 16-1/2” – Pedestal
4 – 1×8 at 14-1/2” – Drawer Boxes
4 – 1×8 at 15-1/2” – Drawer Boxes
2 – ¼” plywood at 15-1/2” x 16” – Drawer Bottoms
1 – ½” plywood at 10-1/8” x 18” – Lower Drawer Front
1 – ½” plywood at 10-3/4” x 18” – Upper Drawer Front
10- ¼” plywood at 1-1/2” x 18” – Trim Slats

Instructions

Read through the entire set of instructions and all comments before beginning this project. If you print out or save our plans, be sure to check back before starting your build, to be sure you have the most up to date set of plans. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using.

Step 1

Edge banding should be applied to all exposed edges of the plywood before assembly.

Cut the pieces for the sides and bottom. Set the Kreg jig for ¾” material and drill pocket holes at each end of the bottom as well as the top of the sides. Attach the bottom to the sides using glue and 1-1/2” pocket hole screws.

Step 2

Cut the piece for the top. Attach to the sides with 1-1/2” pocket hole screws through the holes in the side pieces into the top.

Step 3

Cut the piece for the back. After checking the cabinet for square, attach using glue and 5/8” brad nails.

Step 4

Cut the pieces for the pedestal. Drill pocket holes in each end of the shorter pieces to make a frame. Also drill pocket holes in one long edge of each piece to attach to the bottom of the cabinet. Use glue and 1-1/2” pocket hole screws to attach the pedestal. There will be a 3/4” border around the pedestal.

Step 5

Cut the pieces for the drawer boxes. Assemble as shown using glue and 1-1/2” pocket hole screws.

Cut the pieces for the bottoms. Attach using glue and 5/8” brad nails.

Attach the drawer slide hardware according to the manufacturer’s instructions at the measurements shown in the drawings.

Step 6

Cut the pieces for the drawer fronts. Attach to the front of the drawer boxes using glue and 1” screws placed where they will be hidden by the trim slats.

Cut the pieces for the trim slats and attach to the drawer fronts using glue and 5/8” brad nails.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired.

VN:F [1.9.21_1169]
Rating: 7.3/10 (3 votes cast)
VN:F [1.9.21_1169]
Rating: 0 (from 0 votes)
Stria Nightstand Woodworking Plans, 7.3 out of 10 based on 3 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally