Latest Items

toddler bed woodworking plans

Added/Modified on April 27, 2015
VN:F [1.9.21_1169]
Rating: +1 (from 1 vote)
VN:F [1.9.21_1169]
Rating: 5.2/10 (6 votes cast)

Dimensions:
Dimensions are shown above. Make sure you measure your mattress (designed for a 28″ x 52″ crib mattress) and also, be aware of the height of the canopy. You can make yours taller if you would like.

Shopping List:

4 – 1×6 @ 8 feet long
1 – 1×12 @ 4 feet long
6 – 2×2 @ 8 feet long
2 – 1×3 @ 8 feet long
More 1x3s (4) or 1/2″ plywood for the mattress supports
1 1/4″ pocket hole screws

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
jigsaw
sander
level
countersink drill bit

Cut List

7 – 1×6 @ 28″ (Headboard and Footboard Planks)
4 – 2×2 @ 58 1/2″ (Legs)
2 – 1×3 @ 28″ (Canopy Top/Bottom)
2 – 1×6 @ 52″ (Siderails)
2 – 1×3 @ 52″ (Canopy Sides)
2 – 2×2 @ 52″ (Cleats)
2 – 1×12 @ 15″ (Decorative Side, Top)
2 – 1×12 @ 8 1/2″ (Decorative Side, Bottom)
12 – 1×3 @ 28″ OR 1/2″ plywood 28″ x 52″ (Mattress Bottom)

General Instructions

It is highly recommended for this bed that you use a Kreg Jig™ to predrill all holes. This will make the bed stronger and easier to build, and keep your decorative sides in place. Mark and drill all pocket holes before beginning to build.

Step 1

Headboard Begin by attaching all the headboard boards together as shown above with pocket hole screws and glue. Make sure you rotate the grain of the wood (bark side out, bark side in and so on) so that the panel won’t warp in one direction over time as you attach the planks. Cut the arch out of the top board. Then attach the planks to two of the legs as shown above.

Step 2

Footboard Build the footboard as you did the footboard, but use one less plank.

Step 3

Canopy Add the canopy tops with pocket holes and glue.

Step 4

Joining Headboard/Footboard You may wish to do this inside your room as the size of the bed is getting quite large at this stage. Pocket holes will do the trick, but you could also opt for metal brackets.

Step 5

Cleats You could actually attach the cleats to the siderails independent of the bed. Use 2″ screws and glue. Predrill and countersink your screws, approximately every 8″ down the length of the cleat from the inside.

Step 6

Top Side Now take the longer 1×12 pieces and mark out a pattern as shown above, using the measurements in the diagram to guide you. Carefully cut out with the jigsaw. Once one is cut, use it as a pattern for the other. Sand your cut well. Attach the side to the headboard and siderail with pocket hole screws. Avoid glue on the headboard joint so that you can disassemble the bed if needed.

Step 7

Bottom Sides Same thing on the bottom as the top. Use the shorter 1x12s and measure and cut out. Sand well and attach to the siderails and the legs.

Step 8

Slats I’m so torn on this one. My daughter loves to jump, and the crib mattresses are so flimsy. But a full sheet of plywood instead of slats doesn’t give much air movement for accidents. Do what works for your child and your mattress. You could use 1×3 slats as shown above or 1/2″ plywood over the cleats (use scrap 2x2s to build joists – you will have enough 2x2s in scraps for this).

Step 9

Icing Doesn’t need it, but would be cute! Look in the curtain aisle or the craft wood section for unfinished wood finials. They should be relatively cheap, and need to be less than 1 1/2″ diameter at the base

VN:F [1.9.21_1169]
Rating: 5.2/10 (6 votes cast)
VN:F [1.9.21_1169]
Rating: +1 (from 1 vote)
toddler bed woodworking plans, 5.2 out of 10 based on 6 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally