Latest Items

triple console cabinet woodworking plans

Added/Modified on January 24, 2016
VN:F [1.9.21_1169]
Rating: +2 (from 2 votes)
VN:F [1.9.21_1169]
Rating: 6.0/10 (3 votes cast)


Shopping List:

3 sets euro style bottom corner mount drawer slides, 16” length
3 – sets inset hinges
24 – cup style handles
8 – 2×2 @ 8 feet long
6 – 1×3 @ 8 feet long
6 – 1×2 @ 8 feet long
1 sheet ¾” plywood (get 1 ½” sheets if you want shelves)
2 – 1×6 @ 10 feet long
1 ¼” and 2 ½” PH screws
Wood glue

Tools:

measuring tape
square
pencil
safety glasses
hearing protection
Kreg Jig™
drill
circular saw
table saw
nailer
sander
level

Cut List:

FACE FRAMES
2 – 2×2 @ 72”
8 – 2×2 @ 34 ½”
9 – 2×2 @ 22”

DOOR/DRAWER FACES
24 – 1×3 @ 21 ¾”
18 – 1×2 @ 21 ¾”
6 – 1×2 @ 22 ½”

MAIN BOX
4 – 2×2 @ 15 ¾”
2 – 1×16 @ 69”
4 – 1×16 @ 31”

DRAWERS - CUT TO FIT YOUR CABINET
4 – 1×2 @ 15 ¾” (slide supports)
6 – 1×6 @ 19 ½”
6 – 1×6 @ 17”

General Instructions

Please read through the entire plan and all comments before beginning this project. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain.

Step 1

You’ll probably want shelves, so go ahead and get the extra sheet of plywood, and just have all the plywood ripped into 15 ¾” wide strips, referred to as 1x16s throughout this plan. BUT if you don’t want shelves, or have some scraps to use up, step 1 photo (above) shows you how you can get all the pieces on a single sheet.

Step 2

Note: Back face frame does not have the middle drawer dividers (2×2 @ 22”)

Step 3

You’ll want to build your doors now to fit the frame. Trust me on this one, lining up 11 boards and getting them all square is going to be a trick. Use the frame to help you build the door faces now.

On second thought – I’d recommend a 1×3 here on the back but a 1×2 will do the trick. Just a little more to bite into.

Once your doors are done, you can put aside.

TIP: Test your drawer face boards for fit at this step too – everything is easier to do when your frame is laying flat down.

Step 4

Now connect the two frames. Use glue and screws and check for square.

Step 5

Now attach bottom inside frame.

Step 6

And then sides. Check everything for square here.

Step 7

And then add the dividers. Keep dividers flush to inside compartment.

Step 8

These guys are for attaching your drawer slides to later on. They only go on the outer compartments, and are not needed on middle compartment.

Step 9

You’ll need to build three drawers. A note on drawers – build to suit the finished opening of your cabinet and your drawer slides. The measurements I give are for a perfect build with perfect boards for drawer slides that use 1/2″ space. Build to suit your cabinet for best fit.

Step 10

Install the drawers so they are inset 3/4″ on the front to allow for the drawer faces. They are nice deep drawers!

Step 11

And then attach the drawer faces to front. Keep an even 1/8″ gap around all sides of drawer faces.

Step 12

And finally add the top!

Step 13

You can also add shelves, either fixed or with shelf pins.

And then if you want to put a back on, simply cut a piece of 1/4″ plywood to the overall back size minus 1/2″ and nail and glue on.

Finishing Instructions:

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

VN:F [1.9.21_1169]
Rating: 6.0/10 (3 votes cast)
VN:F [1.9.21_1169]
Rating: +2 (from 2 votes)
triple console cabinet woodworking plans, 6.0 out of 10 based on 3 ratings

Comments

comments


Powered By SageFox. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
SageFox PowerPoint - PowerPoint Slides - PowerPoint Images - Social Tags - Woodworking Plans - eLiquid eJuice | Health Remedies - DIY Ally